What Happened To Dean Vagnozzi, Articles C

Used or spent dry batteries of both non-rechargeable and rechargeable designs, with a marked rating up to 9-volt that are combined in the same package and transported by highway or rail for recycling, reconditioning, or disposal are not subject to this special provision or any other requirement of the HMR. B25 Packagings must be made from monel or nickel or monel-lined or nickel-lined steel. B16 The lading must be completely covered with nitrogen, inert gas or other inert materials. 165 These substances are susceptible to exothermic decomposition at elevated temperatures. B115 Rail cars, highway trailers, roll-on/roll-off bins, or other non-specification bulk packagings are authorized. TP16 The portable tank must be protected against over and under pressurization which may be experienced during transportation. TP31 This hazardous material may only be transported in tanks in the solid state. B57 Class 115A tank car tanks used to transport chloroprene must be equipped with a non-reclosing pressure relief device of a diameter not less than 305 mm (12 inches) with a maximum rupture disc pressure of 310 kPa (45 psig). TP19 The calculated wall thickness must be increased by 3 mm at the time of construction. The Associate Administrator may except from the requirements of this subchapter articles, machinery, and apparatus provided: a. The rechargeable (and some non-rechargeable) types have gelled alkaline electrolytes (rather than acidic) making it difficult for them to generate hydrogen or oxygen when overcharged and therefore, differentiating them from non-spillable batteries. (a) The Hazardous Materials Table . Tank car tanks must have a test pressure rating of 1,379 kPa (200 psig). A stimulating mechanism must be used to initiate one article in the middle of the packaging. Additionally, the offeror must notify the carrier if the tank pressure rise exceeds 3 psig over any 24-hour period. This document is available in the following developer friendly formats: Information and documentation can be found in our B13 A nonspecification cargo tank motor vehicle authorized in 173.247 of this subchapter must be at least equivalent in design and in construction to a DOT 406 cargo tank or MC 306 cargo tank (if constructed before August 31, 1995), except as follows: a. Packagings equivalent to MC 306 cargo tanks are excepted from the certification, venting, and emergency flow requirements of the MC 306 specification. 34 The commercial grade of calcium nitrate fertilizer, when consisting mainly of a double salt (calcium nitrate and ammonium nitrate) containing not more than 10 percent ammonium nitrate and at least 12 percent water of crystallization, is not subject to the requirements of this subchapter. d. Except for transportation by aircraft, neutron radiation detectors and radiation detection systems containing such detectors transported in accordance with paragraph a of this special provision are not subject to the labeling and placarding requirements of part 172 of this subchapter. 38 If this material shows a violent effect in laboratory tests involving heating under confinement, the labeling requirements of Special Provision 53 apply, and the material must be packaged in accordance with packing method OP6 in 173.225 of this subchapter. If you have comments or suggestions on how to improve the www.ecfr.gov website or have questions about using www.ecfr.gov, please choose the 'Website Feedback' button below. In addition, a container exceeding 4 fluid ounces volumetric capacity (7.22 cubic inches) or containing more than 65 grams of fuel may not be connected or manifolded to a lighter or similar device and must also be described and packaged according to the fuel contained therein. Each IBC may not exceed a maximum net quantity of 1,000 kg: a. Testing must be performed or witnessed by a person who is approved by the Associate Administrator (see 173.56(b) of this subchapter). When Column 7 refers to a special provision for a hazardous material, the meaning and requirements of that special provision are as set forth in 172.102 of this subpart. Wall thickness must be verified ultrasonically at intervals midway between periodic hydraulic tests (every 2.5 years). Subpart BTable of Hazardous Materials and Special Provisions 172.101 Purpose and use of haz-ardous materials table. The provisions of this special provision will be effective until January 2, 2023, unless we terminate them earlier or extend them beyond that date by notice of a final rule in the Federal Register. During transport, it must be protected from direct sunshine and stored (or kept) in a cool and well-ventilated place, away from all sources of heat. d. A chemical under pressure with components meeting the properties of: Class 1 (explosives); Class 3 (liquid desensitized explosives); Division 4.1 (self-reactive substances and solid desensitized explosives); Division 4.2 (substances liable to spontaneous combustion); Division 4.3 (substances which, in contact with water, emit flammable gases or toxic gases); Division 5.1 (oxidizing substances); Division 5.2 (organic peroxides); Division 6.2 (Infectious substances); or, Class 7 (Radioactive material), must not be offered for transportation under this description. On the basis of the results of suitable burning rate tests, and taking into account the standard tests in the UN Manual of Tests and Criteria, Part III, subsection 33.2.1 (IBR, see 171.7 of this subchapter), nitrocellulose membrane filters in the form in which they are to be transported that do not meet the criteria for a Division 4.1 material are not subject to the requirements of this subchapter. 31 Materials which have undergone sufficient heat treatment to render them non-hazardous are not subject to the requirements of this subchapter. B59 Water-tight, sift-proof, closed-top, metal-covered hopper cars are also authorized provided that the lading is covered with a nitrogen blanket. Model rocket motors containing 30 grams or less propellant are classed as Division 1.4S and items containing more than 30 grams of propellant but not more than 62.5 grams of propellant are classed as Division 1.4C. Solid substances transported or offered for transport above their melting point are authorized for transportation in portable tanks conforming to the provisions of portable tank instruction T4 for solid substances of packing group III or T7 for solid substances of packing group II, unless a tank with more stringent requirements for minimum shell thickness, maximum allowable working pressure, pressure-relief devices or bottom outlets are assigned in which case the more stringent tank instruction and special provisions shall apply. 50 Cases, cartridge, empty with primer which are made of metallic or plastic casings and meeting the classification criteria of Division 1.4 are not regulated for domestic transportation. The suitability for transport in tanks must be demonstrated using test 8(d) in Test Series 8 (see UN Manual of Tests and Criteria, Part 1, Sub-section 18.7) (IBR, see 171.7 of this subchapter) or an alternative means approved by the Associate Administrator. B133 Hydrochloric acid concentration not exceeding 38%, in Packing Group II, is authorized to be packaged in UN31H1 or UN31HH1 intermediate bulk containers when loaded in accordance with the requirements of 173.35(h) of this subchapter. This web site is designed for the current versions of b. air bag inflators, air bag modules, seat-belt pretensioners, and pyromechanical devices containing Class 1 (explosive) materials or materials of other hazard classes. Column 1 uses six symbols to identify hazardous materials with special shipping conditions such as restrictions for air, domestic, international, or water vessel transport. In addition, MC 312 and DOT 412 cargo tank motor vehicles must: a. B18 Open steel hoppers or bins are authorized. Transportation of these packages also requires the door of each van trailer to be marked with Warning trailer may contain chemical vapor. per pound of hydrogen peroxide solution. Primary receptacles must be further packed in non-specification bulk outer packagings such as cubic yard boxes, plastic rigid-wall bulk containers, dump trailers, and roll-off containers. 386 When transported by private motor carrier only, the following corrosive liquids may be packaged in polyethylene bottles with a capacity no greater than 3.785 L (one gallon), further packed inside an open-top, heavy wall, high density polyethylene box (i.e., crate) in a manner that the polyethylene bottles are not subjected to any superimposed weight, and the boxes must be reasonably secured against shifting within the transport vehicle and loaded so as to minimize the possibility of coming in contact with other lading: Compounds, cleaning liquid, NA1760, PG II or III; Corrosive liquid, acidic, inorganic, n.o.s., UN3264, PG II; Corrosive liquid, acidic, organic, n.o.s., UN3265, PG III; Corrosive liquid, basic, inorganic, n.o.s., UN3266, PG II; Hydrochloric acid solution, UN1789, PG II; and. A51 For aircraft batteries, irrespective of the quantity limitations specified in Column (9A) of the 172.101 Table or 175.75(c), wet cell batteries, UN2794 or UN2795, up to a limit of 100 kg net mass per package may be transported aboard passenger aircraft. 15, 1976, unless otherwise noted. site when drafting amendatory language for Federal regulations: The portable tank must not be used if the wall thickness is less than that prescribed by the applicable T code in Column (7) of the Table for this material. 113 The sample must be given a tentative approval by an agency or laboratory in accordance with 173.56 of this subchapter. Stacking is permitted two or more levels high to achieve maximum allowable utilization of the designated vehicle, rail car weight, or intermodal freight container weight or vessel hold volume. A copy of the approval shall accompany the shipping papers. For UN2031 with more than 55% nitric acid, rigid plastic IBCs and composite IBCs with a rigid plastic inner receptacle are authorized for two years from the date of IBC manufacture. 46 This material must be packed in accordance with packing method OP6 (see 173.225 of this subchapter). A19 Combination packagings consisting of outer fiber drums or plywood drums, with inner plastic packagings, are not authorized for transportation by aircraft. The set to discharge for the spring loaded pressure relief device and the burst pressure for the frangible disc, as applicable, must not be greater than 2.65 bar for portable tanks with minimum test pressures greater than 4 bar; b. 115 Boosters with detonator, detonator assemblies and boosters with detonators in which the total explosive charge per unit does not exceed 25 g, and which will not mass detonate and undergo only limited propagation in the shipping package may be assigned to 1.4B classification code. Additionally, self-propelled vehicles or equipment that contain a fuel cell engine must be described using the entries Engine, fuel cell, flammable gas powered or Engine, fuel cell, flammable liquid powered or Vehicle, fuel cell, flammable gas powered or Vehicle, fuel cell, flammable liquid powered, as appropriate. For transportation by aircraft, as an inner packaging of a combination packaging with a maximum gross mass of 30 kg when packaged as a limited quantity in accordance with 173.27(f). (2) A codes. b. - Other Regulations Relating to Transportation, - Pipeline and Hazardous Materials Safety Administration, Department of Transportation, - Hazardous Materials Table, Special Provisions, Hazardous Materials Communications, Emergency Response Information, Training Requirements, and Security Plans, - Table of Hazardous Materials and Special Provisions, https://www.ecfr.gov/current/title-49/subtitle-B/chapter-I/subchapter-C/part-172/subpart-B/section-172.102. The proper shipping name Paint related material may be used for consignments of packages containing Paint and Paint related material in the same package; b. 56 A means to interrupt and prevent detonation of the detonator from initiating the detonating cord must be installed between each electric detonator and the detonating cord ends of the jet perforating guns before the charged jet perforating guns are offered for transportation. contact the publishing agency. Batteries must be securely cushioned and packed to prevent shifting which could loosen terminal caps or reorient the terminals to produce short circuits. 147 This entry applies to non-sensitized emulsions, suspensions, and gels consisting primarily of a mixture of ammonium nitrate and fuel, intended to produce a Type E blasting explosive only after further processing prior to use. Column 7 specifies codes for special provisions applicable to hazardous materials. However, the design stress limits may not exceed 25 percent of the stress for 0 temper at the maximum design temperature of the cargo tank, as specified in the Aluminum Association's Aluminum Standards and Data (IBR, see 171.7 of this subchapter). This molecular arrangement is exactly the same as that for dithioketo QA [5]. N89 When steel UN pressure receptacles are used, only those bearing the H mark are authorized. 181 When a package contains a combination of lithium batteries contained in equipment and lithium batteries packed with equipment, the following requirements apply: a. A6 For combination packagings, if plastic inner packagings are used, they must be packed in tightly closed metal receptacles before packing in outer packagings. Column 7 Lists the additional (special) provisions that apply to this material. 160 This entry applies to safety devices for vehicles, vessels or aircraft, e.g. An unused lighter or a lighter that is cleaned of residue and purged of vapors is not subject to the requirements of this subchapter. N6 Battery fluid packaged with electric storage batteries, wet or dry, must conform to the packaging provisions of 173.159 (g) or (h) of this subchapter. **Self-reactive materials that are thermally unstable and that Formaldehyde solutions not containing methanol and not meeting the Class 3 flammable liquid criteria must be described using a different proper shipping name. Lead compounds that have a solubility of 5% or less in accordance with this special provision are not subject to the requirements of this subchapter that pertain to Marine Pollutants. Examples of equipment are lawnmowers, cleaning machines, or model boats and model aircraft. Orientation markings as described in 172.312(a)(2) are required when liquid hazardous materials may escape due to incorrect orientation. The in-page Table of Contents is available only when multiple sections are being viewed. 175 This substance must be stabilized when in concentrations of not more than 99%. N5 Glass materials of construction are not authorized for any part of a packaging which is normally in contact with the hazardous material. 64 The group of alkali metals includes lithium, sodium, potassium, rubidium, and caesium. N75 Packages consisting of tightly closed inner packagings of glass, earthenware or metal, securely cushioned and packed in outer wooden barrels or wooden or fiberboard boxes, capacity not over 2.5 kg (5.5 pounds) net weight, are authorized and need not conform to the requirements of part 178 of this subchapter. Fertilizers meeting the criteria for this identification number are only subject to the requirements of this subchapter when offered for transportation and transported by air or vessel. The objects must be secured to the flat car, motor vehicle, intermodal container, or unitized by steel banding to wooden runners or pallets and the units secured to the flat car, motor vehicle, or freight container to prevent shifting, including relative motion between the objects, under conditions normally incident to transportation. The outside of each package must be plainly marked ARTICLES, EXPLOSIVES, N.O.S. 169 This entry applies to lighter refills (see 171.8 of this subchapter) that contain a Division 2.1 (flammable) gas but do not contain an ignition device. Dry batteries specifically covered by another entry in the 172.101 Table must be transported in accordance with the requirements applicable to that entry. 365 For manufactured instruments and articles containing mercury, see UN3506. FAR). This content is from the eCFR and may include recent changes applied to the CFR. 328 When lithium metal or lithium ion batteries are contained in the fuel cell system, the item must be described under this entry and the appropriate entries for Lithium metal batteries contained in equipment or Lithium ion batteries contained in equipment. Each empty bottle must have a minimum weight of not less than 140 grams and a minimum wall thickness of not less than 0.020 inch (0.508 mm). switch to drafting.ecfr.gov. Single unit tank car tanks must have a reclosing pressure relief device having a start-to-discharge pressure set at no more than 1551 kPa (225 psig). The requirements of 173.24(g)(1) and 173.27(c) do not apply. TP4 The maximum degree of filling for portable tanks must not exceed 90%. (1) Even though certain packagings are specified in this part, it is, nevertheless, the responsibility of the person offering a hazardous material for transportation to ensure that such packagings are compatible with their lading. The tank must have been designed and constructed to be capable of withstanding full vacuum. Regulation Y A7 Steel packagings must be corrosion-resistant or have protection against corrosion. TP5 For a portable tank used for the transport of flammable refrigerated liquefied gases or refrigerated liquefied oxygen, the maximum rate at which the portable tank may be filled must not exceed the liquid flow capacity of the primary pressure relief system rated at a pressure not exceeding 120 percent of the portable tank's design pressure. The letter codes are placed in front of the number codes (for example, "A29"). Outage must be sufficient to prevent tanks from becoming liquid full at 55 C (130 F). If a tank car tank is equipped with a reclosing pressure relief valve, the tank must also be equipped with a vacuum relief valve. Specification IBCs and FIBCs are to be secured to a pallet. 125 Lactose or glucose or similar materials may be used as a phlegmatizer provided that the substance contains not less than 90%, by mass, of phlegmatizer. 369 In the case of non-fissile or fissile-excepted uranium hexafluoride, the material must be classified under UN 2978. Packagings of other material with a small amount of metal, for example metal closures or other metal fittings such as those mentioned in part 178 of this subchapter, are not considered metal packagings. In addition to the provisions applicable to the transport of Division 6.1 substances, the provisions of 173.421(c) and 173.443(a) of this subchapter apply. 173 For adhesives, printing inks, printing ink-related materials, paints, paint-related materials, and resin solutions which are assigned to UN3082, and do not meet the definition of another hazard class, metal or plastic packaging for substances of packing groups II and III in quantities of 5 L (1.3 gallons) or less per packaging are not required to meet the UN performance package testing when transported: a. 197 The nitrocellulose must meet the criteria of the Bergmann-Junk test or methyl violet paper test in the UN Manual of Tests and Criteria, Appendix 10 (IBR, see 171.7 of this subchapter). is the mean coefficient of cubical expansion of the liquid between the mean temperature of the liquid during filling (tf) and the maximum mean bulk temperature during transportation (tr) both in degrees celsius. c. The time between offering the material for transportation at the point of origin, and unloading the material at the destination does not exceed 48 hours. 23 This material may be transported under the provisions of Division 4.1 only if it is so packed that the percentage of diluent will not fall below that stated in the shipping description at any time during transport. Terminal protection methods include but are not limited to the following: (i) Securely attaching covers of sufficient strength to protect the terminals; (ii) Packaging the battery in a rigid plastic packaging; or. TP2 a. If the material has a flash point of less than 38 C (100 F), then the bulk packaging requirements of 173.242 of this subchapter are applicable. R1 A person who offers for transportation tank cars containing sulfur, molten or residue of sulfur, molten may reference the Sulfur Institute's, Molten Sulphur Rail Tank Car Guidance document (see 171.7 of this subchapter) to identify tank cars that may pose a risk in transportation due to the accumulation of formed, solid sulfur on the outside of the tank. Other inorganic nitrate salts may replace part of the ammonium nitrate. B80 Each cargo tank must have a minimum design pressure of 276 kPa (40 psig). 65 The group of alkaline earth metals includes magnesium, calcium, strontium, and barium. "Published Edition". See also UN1942 in the 172.101 Hazardous Materials Table. A30 Ammonium permanganate is not authorized for transportation on aircraft. For vessel transport, the palletized loads, pallet boxes or unit load devices must be firmly packed and secured in closed cargo transport units; or. (7) Special Provisions (172.102) IB8, IP2, IP4 (iii) Constructing the battery with terminals that are recessed or otherwise protected so that the terminals will not be subjected to damage if the package is dropped. Column 7 of the HMT specifies codes for special provisions applicable to packaging, packaging requirements, certification, and marking or labeling for a hazardous material. b. c. Where the liquid or solid components are classed as Division 6.1, Packing Group II or III, or Class 8, Packing Group II or III, the chemical under pressure must be assigned a subsidiary risk of Division 6.1 or Class 8 and the appropriate identification number must be assigned. (iii) A copy of the test results must be kept on file at each facility where packagings are offered for transportation, and must be made available to a representative of the Department upon request. (3) A flammable gas is a gas that meets the criteria in 173.115 of this subchapter. The letter Z shown in the marking code for composite IBCs must be replaced with a capital code letter designation found in 178.702(a)(2) of this subchapter to specify the material used for the other packaging. This may be fulfilled by an additional locking device linked to the activator; (4) Each article must be manufactured in such a way as to prevent hazardous projections of the pressure receptacle or parts of the pressure receptacle; (5) Each pressure receptacle must be manufactured from material which will not fragment upon rupture; (6) The design type of the article must be subjected to a fire test. Energy storage capacity means the energy held by a capacitor, as calculated using the nominal voltage and capacitance. 145 This entry applies to formulations that neither detonate in the cavitated state nor deflagrate in laboratory testing, show no effect when heated under confinement, exhibit no explosive power, and are thermally stable (self-accelerating decomposition temperature (SADT) at 60 C (140 F) or higher for a 50 kg (110.2 lbs.) A series of notes is used throughout TABLE 1 and TABLE 2 to provide additional information concerning certain hazardous substances. 121 This substance, when containing less alcohol, water or phlegmatizer than specified, may not be transported unless approved by the Associate Administrator. (TOY CAPS) - HANDLE CAREFULLY OR TOY CAPS - HANDLE CAREFULLY; and. (8) A code containing the letters TP refers to a portable tank special provision for UN or IM Specification portable tanks that is in addition to those provided by the portable tank instructions or the requirements in part 178 of this subchapter. The guns are packaged in accordance with Packing Method US 1 as specified in 173.62 of this subchapter. b. N4 For combination or composite packagings, glass inner packagings, other than ampoules, are not permitted. Column 7: Special Provisions - Specifies codes for special provisions applicable to some hazardous materials. These provisions can be classified even further with each form of transportation. It is not an official legal edition of the CFR. The quantities of hazardous materials do not exceed those specified in 173.4a of this subchapter; and. Such articles must comply with the following requirements: (1) The water capacity of the pressure receptacle must not exceed 0.5 L and the working pressure must not exceed 25 bar at 15 C (59 F); (2) The minimum burst pressure of the pressure receptacle must be at least four times the pressure of the gas at 15 C (59 F); (3) Each article must be manufactured in such a way that unintentional firing or release is avoided under normal conditions of handling, packing, transport and use.